Welcome to All Things Stainless

Browse



Wire Balustrade Kits

There are many combinations of fittings (click here to view our fittings image gallery) that can be used in balustrading. We have combined the most common fittings into our balustrade DIY Kits. Each kit contains all the fittings required to complete one strand of wire.

Each kit contains fittings for the two end posts. These are usually Saddles (for steel or timber posts) or Lag Screws (for timber posts, brick or concrete walls (use with raw plugs). The kit also contains the fittings for the ends of the wire, one of which will be a
Rigging Screw or Turnbuckle to tension the wire.

One Kit can span up to 10 meters. You will usually run the wire through the
middle of any centre post only terminating on a corner or end post. If the span between ends is greater than 10 meters we would strongly recommend you split the run in half and use 2 lots of kits.

Hand Swaged Wire Balustrading Kits

Hand swaged kits use a Thimble and Ferrule
at each end of the wire to make a loop
that the fittings are then connected to. When using Hand Swaged kits you will need to put your wires together onsite after the wire has been passed through any centre post. A Hand Swaging tool will be requied if using this type of kit.

Pre-Swaged DIY Balustrade Kits

Pre-Swaged kits come ready made to length (supplied by you at time of purchasing) with fittings Hydraulically Pressed (swaged) to the ends of the wire. Examples of the fittings that are hydraulically swaged are Fork Terminals
and Jaw/Swage Rigging Screws
.
These are the easiest kits to use and no special tools are required. When puchasing this type of kit we will require the inside to inside post measurements of your two end posts. You can still pass the wire through any centre post by drilling an 8mm hole.

Each wire has +- 30mm from the measurement provided. If your posts are not 100% vertical you should supply the average length for us to make the wires to.

Wire Required

All kits are suited to 3.2mm wire. Hand Swaged kits should use 7x7 3.2mm wire and Pre-Swaged Kits should use 1x19 3.2mm wire. You should note that Hand Swaged Kits can NOT be used with 1x19 wire.

How many wires should you use?

Visit our Balustrade Regulaions page for more info.

Make sure you click on the product details link for each kit to find out more information about the kit.







Order by:     Display #  

Hand Swaged DIY Kit - Sample Pack

Hand Swaged DIY Kit Sample pack(Max. 1 per order)
1 x 1000mm length of 7x7 3.2mm wire
1 x Jaw/Jaw Rigging Screw
1 x Eye/Eye Turnbuckle
1 x hook/eye turnbuckle
1 x 6mm Lag Screw
1 x 5mm Saddle
1 x Saddle Screw
1 x Po  Product Details...

$7.40 (including 10 % tax)

Pre-Swaged DIY Kit - Sample Pack

Pre-Swaged DIY Kit Sample pack
1 x 1000mm length of 3.2mm 1x19 wire with a Fork Terminal Swage at one end and a Jaw/Swage Rigging Screw at the other
1 x 6mm Lag Screw
1 x 5mm Saddle
1 x Saddle Screw
1 x Pop-Rivet
1 x Nylon Gr  Product Details...

$7.40 (including 10 % tax)

Hand Swaged DIY Kit - Eye/Eye Turnbuckles & Saddles

Hand Swaged DIY Kit for Balustrading using Eye/Eye Turnbuckles & Saddles

Kit Includes
1 x 5mm Eye/Eye Turnbuckle
2 x Saddles
4 x Stainless Screws or Pop-Rivets
2 x 3mm Thimble
2 x 3mm Ferrule (swage)
Use 7x7 3.2mm wire with this k  Product Details...

$8.10 (including 10 % tax)
$7.40 (including 10 % tax)
You Save: $0.70

Hand Swaged DIY Kit - Hook/Eye Turnbuckles & Saddles

Hand Swaged DIY Kit for Wire Balustrading using Hook/Eye Turnbuckles & Saddles

Kit Includes
1 x 5mm Hook/Eye Turnbuckle
2 x Saddles
4 x Stainless Screws or Pop-Rivets
2 x 3mm Thimble
2 x 3mm Ferrule (swage)
  Product Details...

$8.95 (including 10 % tax)
$7.80 (including 10 % tax)
You Save: $1.15

Hand Swaged DIY Kit - Jaw/Jaw Rigging Screw & Saddles

Hand Swaged DIY Kit for Balustrading using Saddles

Kit Includes
2 x Saddles
4 x Stainless Screws or Pop Rivets
1 x Jaw/Jaw Rigging Screw
2 x 3mm Thimble
2 x 3mm Ferrule (swage)
Use 7x7 3.2mm wire with this kit
  Product Details...

$9.80 (including 10 % tax)
$9.00 (including 10 % tax)
You Save: $0.80

Hand Swaged DIY Kit - Jaw/Jaw Rigging Screw & Lag screws

Hand Swaged DIY Kit for Balustrading using lag screws.

Kit Includes
2 x 6mm Lag Screws
1 x 5mm Jaw/Jaw Rigging Screw
2 x 3mm Thimble
2 x 3mm Ferrule (swage)
Use 7x7 3.2mm Stainless Steel wire with this kit
  Product Details...

$11.00 (including 10 % tax)
$10.70 (including 10 % tax)
You Save: $0.30

Pre-Swaged - DIY Kit with Saddles

Pre swaged DIY Kit for Balustrading

Kit Includes
2 x 5mm Saddles
4 x Saddle Screws
1 x 3mm Jaw/Swage Rigging Screw
1 x 3mm Fork Terminal Swage
Hydralic Swaging of the fittings to the wire
  Product Details...

$15.40 (including 10 % tax)
$13.80 (including 10 % tax)
You Save: $1.60

Pre-Swaged - DIY Kit with Lag Screws

Pre swaged DIY Kit for Balustrading

Kit Includes
2 x 6mm Lag Screws
1 x 3mm Jaw/Swage Rigging Screw
1 x 3mm Fork Terminal Swage
Hydralic Swaging of the fittings to the wire
  Product Details...

$16.60 (including 10 % tax)
$15.30 (including 10 % tax)
You Save: $1.30

Nylon Grommets

Split Grommets
Suitable for 3.2mm or 4mm wire
Fits into an 8.5mm Hole
Suitable for steel or timber
  Product Details...

$0.20 (including 10 % tax)

C Spanner for M5 Rigging Screws

This simple to use spanner will make tightening your M5 Rigging Screws a breeze. Suitable for both M5 Jaw/Jaw Rigging Screws and Jaw/Swage Rigging Screws  Product Details...

$16.55 (including 10 % tax)
$11.00 (including 10 % tax)
You Save: $5.55

Socket Drive for 6mm Lag Screw

Save time with this 6mm Lag Screw Socket Drive.
Simply use this in your battery drill to quickly screw your lag screws into the post.
  Product Details...

$26.95 (including 10 % tax)
$11.00 (including 10 % tax)
You Save: $15.95

Centre: 50x10mm Post Drilled with 11 holes at 80mm Centres

Use: Centre Post
Length: 960mm
Width: 50mm
Thickness: 10mm
Grade: 316
Finish: Mirror
Holes: 11 (8mm) Holes at 80mm Centres
  Product Details...

$145.00 (including 10 % tax)
$110.00 (including 10 % tax)
You Save: $35.00

Hand Swaging Tool

Hand Swaging Tool
To swage 2mm, 2.5mm and 3.2mm Ferrules
  Product Details...

$80.00 (including 10 % tax)
$70.00 (including 10 % tax)
You Save: $10.00

Wire Cutters

Suitable for 1.6mm, 2.5mm, 3.2mm Wire
  Product Details...

$35.00 (including 10 % tax)
$30.00 (including 10 % tax)
You Save: $5.00

316: 3.2mm 1x19 Stainless Steel Wire Rope - 305 Metre Roll

Diameter: 3.2mm
Lay: 1x19 (19 individual strands)
Grade: 316 (Marine Grade) Stainless Steel
Quantity: 305m Roll
Breaking Strain: 848kg
Weight: 15.9kg
  Product Details...

$476.95 (including 10 % tax)
$360.00 (including 10 % tax)
You Save: $116.95

316: 3.2mm 7x7 Stainless Steel Wire Rope - 305 Metre Roll

Diameter: 3.2mm
Lay: 7x7 (49 individual strands)
Grade: 316 (Marine Grade) Stainless Steel
Quantity: 305m Roll
Breaking Strain: 710kg
Weight: 13.1kg
  Product Details...

$362.65 (including 10 % tax)
$250.00 (including 10 % tax)
You Save: $112.65

316: 3.2mm 1x19 Stainless Steel Wire Rope - Per Metre

Diameter: 3.2mm
Lay: 1x19 (19 individual strands)
Grade: 316 (Marine Grade) Stainless Steel
Quantity: 1 metre - Purchase multiple metres by entering in number in the quantity field. You will receive 1 continuous length
Breaking St  Product Details...

$1.65 (including 10 % tax)
$1.30 (including 10 % tax)
You Save: $0.35

316: 3.2mm 7x7 Stainless Steel Wire Rope - Per Metre

Common uses for this wire include:

Balustrading
Plant trainers
Clothes lines
Dog runs
Shade Sails

This is the most common wire used for DIY balustrading. It is a semi-flexible wire and is suitable for use with Thi  Product Details...

$1.25 (including 10 % tax)
$0.99 (including 10 % tax)
You Save: $0.26




Display #  
Last Updated: Friday, 30 June 2017 02:03Joomla SEF URLs by Artio
 
Joomla Templates by Joomlashack