Welcome to All Things Stainless

Browse

There are many combinations of fittings that can be used together to make a Stainless Handrail Post. We have grouped some of the most popular and easiest to use fittings.

A DIY post will usually have 3 main components as listed below.

Upright:

Your Post will usually be for the centre, end or corner.

Centre Posts: You could try using a blank peice of tube and making your centre post from scratch however Stainless Steel Tube is dificult to drill without slipping or scratching it especially if you do not have the correct tools. We recommend buying our pre-drilled tube that can be drilled to your requirements and is usually 11 holes for 80mm spacing and 15 holes for 60mm spacing.

End Posts: Again you could try using blank tube and fastening saddles to your posts yourself however it is very difficult to not only drill the tube but also get the saddles in a straight line. We recommend using our end post tube which has been drilled and Blind Rivets have been inserted. We then use 6mm Eye Screws with a locking nut to fasten your wires to.

Corner Posts: Our corner post tube uses the same fittings as or end posts however has the fittings for the wire to attach to on two sides. The angle the fittings are installed can be made to your specifications. It can be 90 Degrees for a right angle corner or a custom angle if required.

Top:

The top of your post will be determined by the material being used for your handrail. This is usually stainless tube or timber.

If using stainless tube there are several options available.
You can use a 2 Inch perpendicular joiner to connect the post directly to the handrail.
You can use a post reducer with a 1 Inch perpendicular joiner.
You can use an adjustable support (either internal or external fit) that has a radius that is then pop-riveted to the under side of the handrail.

If using a Timber or flat handrail you can use an Oblong flange glued to the post.
You can use a Adjustable Support (either internal or external fit) that has a flat top and is screwed to the underside of the handrail.
You can also use a post reducer with adjustable tee.

Base:

To eliminate the need for welding we recommend using either a Round Base Plate/Flange (glued to the post) or an Adjustable Heavy Duty Base Plate.

Below are all of the items you will need to make your own posts.


Order by:     Display #  

316: 1" Tube 2" Radius Perpendicular Joiner "Flush Fitting

Used to connect 1" tube to 2" tube. Can also be used with Post reducer.

  Product Details...

$16.25 (including 10 % tax)

316: 2" Oblong Base Plate/Flange

Used with 2 Inch tube.
Can be Welded, Pop Riveted or Gluded to the tube.

  Product Details...

$34.20 (including 10 % tax)
$26.00 (including 10 % tax)
You Save: $8.20

316: 2" Round Base Plate/Flange

Used with 2 Tube.
Can be used at the base or top of a post or at the ends of a handrail.
Can be welded or pop-riveted to the tube.

  Product Details...

$35.50 (including 10 % tax)
$26.00 (including 10 % tax)
You Save: $9.50

316: 2" Post Reducer "Tapered"

Use with a Perpendicular Joiner for round tube or a Deck Tee if joining to Timber
Product Details...

$33.65 (including 10 % tax)
$21.00 (including 10 % tax)
You Save: $12.65

316: 2" Tube 2" Radius Perpendicular Joiner "Flush Fittin


$21.95 (including 10 % tax)
$16.80 (including 10 % tax)
You Save: $5.15


2" Adjustable Rail Support Radiused "Internal Fit"


$55.05 (including 10 % tax)
$29.85 (including 10 % tax)
You Save: $25.20

1.5" Adjustable Rail Support Flat Base "Internal Fit"

316 Grade Stainless Steel
Fits inside 1.5" tube with a 1.6mm wall
Can be used as a adjustable top for a stair or ramp post or at the end of a handrail that needs to be installed on an angle
  Product Details...

$40.35 (including 10 % tax)

2" Adj. Rail Support Flat Base "Internal Fit"


$54.70 (including 10 % tax)
$36.80 (including 10 % tax)
You Save: $17.90

2" Adj. Rail Support Radiused "External Fit"


$53.45 (including 10 % tax)
$32.25 (including 10 % tax)
You Save: $21.20

2" Adj. Rail Support Flat Base "External Fit"


$52.10 (including 10 % tax)
$32.25 (including 10 % tax)
You Save: $19.85

2" Blank Post

Length: Up to 1 metre
Diameter: 2" (50.8mm)
Thickness: 1.6mm
Grade: 316
Finish: Mirror
Use: To build your own posts
  Product Details...

$45.00 (including 10 % tax)

Centre: 2" Pre-Drilled Post - Up to 15 Holes

Use: Centre Post
Length: Up to 1 meter (usually 960mm to allow for top rail)
Diameter: 2" (50.8mm)
Thickness: 1.6mm
Grade: 316
Finish: Mirror
Holes: Up to 15 holes drilled to your specifications
Top/Base: Add you own
  Product Details...

$99.50 (including 10 % tax)

60 Gram 2 part Epoxy Glue Set


$16.80 (including 10 % tax)

Centre: Flat Post Drilled with 11 holes at 80mm Centres

Use: Centre Post
Length: 960mm to allow for top rail
Width: 40mm
Thickness: 5mm
Grade: 316
Finish: Satin
Holes: 11 (8mm) Holes at 80mm Centres
  Product Details...

$145.00 (including 10 % tax)

Centre: 50x10mm Post Drilled with 11 holes at 80mm Centres

Use: Centre Post
Length: 960mm
Width: 50mm
Thickness: 10mm
Grade: 316
Finish: Mirror
Holes: 11 (8mm) Holes at 80mm Centres
  Product Details...

$145.00 (including 10 % tax)
$110.00 (including 10 % tax)
You Save: $35.00

1 Inch Tee 90 Degrees


$19.50 (including 10 % tax)




Display #  
Last Updated: Wednesday, 28 June 2017 15:21Joomla SEF URLs by Artio
 
Joomla Templates by Joomlashack